- WiFi Tape Device Slimme Meter Raspberry PI PCB microKIM LED KIM-1 KIM KiCAD imker I2C Herfst Hardware Günther Gloeilamp Firmware ESP8266 ESP32 ESP-01 Energie DSMRloggerAPI DSMR-logger DSMR DS3231 DS18B20 DONOFF Dimmer De Witte Waas Clini-Clown Cassette Beehive BeeHave Avonturen ATTiny84 ATTiny Arduino Alice in Wonderland ADHD Aandewiel
Views
- Recent Projects - 135,866 views
- DSMR-logger V4 (Slimme Meter uitlezer) - 133,690 views
- Home-Assistant Integratie met de DSMR-logger - 121,246 views
- restAPI’s zijn hip! (nieuwe firmware voor de DSMR-logger) - 111,817 views
- Slimme Meter uitlezer - 72,642 views
- Boekbespreking - 29,078 views
- DONOFF – WiFi enabled light dimmer - 27,685 views
- Aan de slag met de ESP8266 - 24,596 views
- Solid State Tape Device for the (micro)KIM - 12,517 views
- Universal InfraRed IoT Learning Remote - 12,252 views
Recent Comments
- Willem Aandewiel on restAPI’s zijn hip! (nieuwe firmware voor de DSMR-logger)
- Ceriel on restAPI’s zijn hip! (nieuwe firmware voor de DSMR-logger)
- Ceriel on DSMR-logger schrijft nu rechtstreeks in InfluxDB / Grafana
- Willem Aandewiel on Yet Another Parametric Projectbox generator
- gerrit on An ESP8266 Ticker
Statistics
- 2,213
- 522,872
- 233,750
- 3,308
- 19,364
Meta
Category Archives: Computer
Yet Another Parametric Projectbox generator
[ ] Een Nederlandse vertaling van deze post kun je hier vinden. With every electronic circuit I make, there comes a moment when the project is “finished”…. almost! The last step is always to find a suitable projectbox and even … Continue reading
Posted in 3D printing, Arduino, Computer, ESP8266, Hardware, Scripts
35 Comments
Nog een geparametriseerde projectbox generator
[ ] Yet Another Parametric Projectbox generator Here you can find an English version of this post. Bij iedere elektronische schakeling die ik maak komt er een moment dat het project “af” is …. bijna! De laatste stap is altijd … Continue reading
Posted in 3D printing, Arduino, Computer, ESP8266, Hardware, Scripts
Tagged 3D, generator, PCB, YAPP, Yet Anaother Parametric Projectbox Generator
16 Comments
digital Tape Recorder for the KIM-1 (and clones)
[ ]In October 2017 I wrote a post with the title “Solid State Tape Device for the (micro)KIM“. Recently one of the makers (Dirk Dral) wanted to adapt the device for use with a genuine KIM-1 and ran into some … Continue reading
Posted in Arduino, Computer, ESP8266, Firmware, Hardware, KiCAD, KIM, Uncategorised, WiFi
Tagged KIM, KIM-1, micro-KIM, microKIM, Tape Device
17 Comments
A 32kb Memory Expansion Board for the microKIM
[ ] As you may know, I own a microKIM (KIM-1 clone) Single Board Computer (SBC). It is a trip down memory lane to work with the incredible simplicity of what was once “top of the bill” technology. The original … Continue reading
Controlling Lots of Relays with only 2 GPIO pins
Piggyback board for 8- or 16-relays boards to control with I2C Continue reading
I2C Rotary Encoder
7,289 views I will address two topics in this post. The first one is about Rotary Encoders and what you can do with them. The second is about the Inter-Integrated Circuit protocol (I²C), developed by Philips. Een in het Nederlands … Continue reading
Posted in Arduino, Computer, ESP8266, Hardware, KiCAD
Tagged ATTiny84, I2C, Rotary Encoder
7 Comments
Universal InfraRed IoT Learning Remote
[ ] In this post I will guide you through the process of building a device that can capture Infrared-messages from an Infrared remote controller (learning mode), and resend the captured Infrared-messages (sending mode). I will use the affordable and … Continue reading